Fulfillment Operations Pages
Last updated
Was this helpful?
Last updated
Was this helpful?
This page displays the number and status of , pack jobs and in various ways to give you an insight into the performance of your stores.
Here you can see the total number of completed entities by date. "Completed" here means that the entities must have reached a successful final status. Final statuses that correspond to a failure (e.g. a cancellation) are not counted.
The assigned date corresponds to the time when the final status was reached. If an entity was reopened and closed again after completion, the time of the second completion is used.
Since tags can be created freely by you, the tag key by which the breakdown is made must be configured for the dashboard. Otherwise this chart will not be visible.
Created pick jobs and successfully closed handover jobs (status HANDED_OVER) are shown here in direct comparison by date so that you can see, for example, how the order processing is keeping up with the load.
These charts show how often pick jobs were finished with which status. For "closed" pick jobs, a distinction is made as to whether they were completely or partially picked.
Here around 40 pick jobs were finished on August 18, but only 16 of them were picked successfully and completely.
Here, 10 order lines with a total quantity of 11 articles were picked on August 3. An article could have had a quantity of 500 grams, for example, but this would only have increased the displayed quantity by 1.
This page is intended to provide detailed information on how long different process steps take within the facilities. The page is divided into two parts: the upper section provides a quick overview of three important durations, while the lower section provides further details on a single selectable duration.
The following three durations are shown both aggregated as a total value and by day/week/month:
Time until picking is the time that elapses between the creation of a pick job and the first time that picking is started. If a pick job is somehow ended, reopened and picked again, this is not taken into account here. An analogous restriction applies to the following periods.
Picking time is the time that elapses between the first time picking is started and the first time a pick job is closed (status CLOSED).
Handover time is the time that elapses between the creation of the handover job and the first time the handover job is closed (status HANDED_OVER).
As there may be many process times of interest, the details are shown for a single selected one of these times. The selection is made using the dropdown in the filter bar:
The following graphs then refer to this selected duration.
This is the total average calculated over all selected dates and facilities.
In addition to the average value per day/week/month, the band within which 80% of all cases lie is also shown here. This allows you to estimate how large typical deviations from the mean value are.
The average value is given per facility, sorted by the highest value. A maximum of 30 facilities are listed.
A high process time alone might not be too alarming if the total number of cases is rather low. For this reason, both values are also plotted against each other in a scatter plot, with each point representing a facility. Attention should be paid to data points in the top right-hand corner, as they indicate facilities with both a high duration and a high instance count. In this example, the rather high number of 373 pick jobs in Berlin was created and then picked. The average time between these events was around 9 hours, which is in the midfield.
This graph shows the frequency of cases where a certain amount of time was required. In the example below, it can be seen that the majority of the selected durations were less than 10 hours. In 560 cases, however, the time was around 33 hours.
This chart breaks down the completed pick jobs according to the value of an . In the example below, orders could have an order tag "customer type", with three possible values "B2B", "B2C" and "Internal". On the selected day, 16 pickjobs were completed for "B2B" customers.
The number of picked order lines and the sum of the picked quantity can be seen here, both per day and in total. For the assignment to a day the time when the respective pick job was closed is used. Articles for which it is known from the that they are not counted in pieces are added with the quantity “1” for each order line.
All durations shown here are arithmetic means, with outliers removed on the basis of anomaly detection. This will be replaced by median/quantile data analogous to the .
